manualshive.com logo in svg

Intel PXA255, Developer'S Manual

The Intel PXA255 product is a high-performance processor designed for a range of mobile devices. Obtain detailed specifications and technical information about this product by downloading the free datasheet and user manual from our website. Experience the power and versatility of Intel PXA255 for your mobile devices.

Share
Download
background image

Intel® PXA255 Processor Developer’s Manual

12-31

 

USB Device Controller

12.6.5.7

Receive FIFO Not Empty (RNE)

The receive FIFO not empty bit indicates that unread data remains in the receive FIFO. This bit 
must be polled when the UDCCSx[RPC] bit is set to determine if there is any data in the FIFO that 

the DMA did not read. The receive FIFO must continue to be read until this bit clears or data will 

be lost.

12.6.5.8

Receive Short Packet (RSP)

The UDC uses the receive short packet bit to indicate that the received OUT packet in the active 

buffer currently being read is a short packet or zero-sized packet. This bit is updated by the UDC 

after the last byte is read from the active buffer and reflects the status of the new active buffer. If 

UDCCSx[RSP] is a one and UDCCSx[RNE] is a 0, it indicates a zero-length packet. If a zero-
length packet is present, the core must not read the data register. UDCCSx[RSP] is cleared when 

the next OUT packet is received.

These are read/write registers. Ignore reads from reserved bits. Write zeros to reserved bits.

12.6.6

UDC Endpoint x Control/Status Register (UDCCS3/8/13)

USCCS3/8/13, shown in 

Table 12-17

, contains 4 bits that are used to operate endpoint(x), an 

Isochronous IN endpoint.

Table 12-17. UDCCS3/8/13 Bit Definitions 

0x4060_001C

0x4060_0030
0x4060_0044

UDCCS3
UDCCS8

UDCC13

USB Device Controller

Bit

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9

8

7

6

5

4

3

2

1

0

reserved

TS

P reserved

TU

R

FT

F

TPC

TFS

Reset X X X X X X X X X X X X X X X X X X X X X X X X 0

0

0

0

0

0

0

1

Bit

Name

Description

31:8

—

reserved

7

TSP

Transmit short packet (read/write 1 to set).
1 = Short packet ready for transmission.

6:4

—

reserved

3

TUR

Transmit FIFO underrun (read/write 1 to clear)
1 = Transmit FIFO experienced an underrun. 

2

FTF

Flush Tx FIFO (always read 0/ write a 1 to set)
1 = 1 – Flush Contents of TX FIFO

1

TPC

Transmit packet complete (read/write 1 to clear).
0 = Error/status bits invalid.
1 = Transmit packet has been sent and error/status bits are valid.

0

TFS

Transmit FIFO service (read-only).
0 = Transmit FIFO has no room for new data
1 = Transmit FIFO has room for at least 1 complete data packet

Summary of Contents for PXA255

























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXA255

3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Brand: Javad Pages: 35
LORD AP5103 Series Technical Manual preview
AP5103 Series
Brand: LORD Pages: 9
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
ekwb EK-Vector Radeon RX5700 + XT Backplate Installation Manual preview
EK-Vector Radeon RX5700 + XT Backplate
Brand: ekwb Pages: 7
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
ZALMAN ZM80C-HP Manual preview
ZM80C-HP
Brand: ZALMAN Pages: 18
Corsair H80i v2 Quick Start Manual preview
H80i v2
Brand: Corsair Pages: 12
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
Billion BiPAC 5200S RC Series User Manual preview
BiPAC 5200S RC Series
Brand: Billion Pages: 79
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Brand: Lindy Pages: 3
ICP DAS USA WF-2572M User Manual preview
WF-2572M
Brand: ICP DAS USA Pages: 26
IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... User Manual preview
32R1860 - Nortel Layer 2/3 Copper GbE Switch...
Brand: IBM Pages: 14
ekwb EK-Quantum Vector FE RTX 3080 User Manual preview
EK-Quantum Vector FE RTX 3080
Brand: ekwb Pages: 20
U-Media WST-375L User Manual preview
WST-375L
Brand: U-Media Pages: 42
Spirent TestCenter Getting Started With preview
TestCenter
Brand: Spirent Pages: 86

Brands by name

Popular brands

Load more brands