Intel PXA255 Developer'S Manual Download Page 522 | Manualshive

Page: 522 / 600

background image

15-18

Intel® PXA255 Processor

Developer’s Manual

MultiMediaCard Controller

3. MMC_SPI[SPI_CS_ADDRESS] must be set to specify the card that the software wants to

address. A 1 enables CS0 and a 0 enables CS1.

Note:

When the card is in SPI mode, the only way to return to MMC mode is by toggling power to the

card.

15.4.4

No Data Command and Response Sequence

For the basic no data transfer, command and response transaction, the software must:

1. Turn the clock off, as described in

Section 15.4.1

.

2. Write the command index in the MMC_CMD[CMD_INDEX] bits.

3. Write the command argument in the MMC_ARGH and MMC_ARGL registers.

4. Write the MMC_CMDAT register set as:

a. Write 0b00 to MMC_CMDAT[RESPONSE_FORMAT].

b. Clear the MMC_CMDAT[DATA_EN] bit.

c. Clear the MMC_CMDAT[BUSY] bit, unless the card may respond busy.

d. Clear the MMC_CMDAT[INIT] bit.

5. Write MMC_RESTO register with the appropriate value.

6. Write 0x1b in MMC_I_MASK to unmask the MMC_I_REG[END_CMD_RES] interrupt.

7. Start the clock, as described in

Section 15.4.1

.

The software must not make changes in the set of registers until the end of the command and

response sequence, after the clock is turned on.

After the clock is turned on, the software must wait for the MMC_I_REG[END_CMD_RES]
interrupt, which indicates that the command and response sequence is finished and the response is

in the MMC_RES FIFO.

The software may then read the MMC_STAT register to verify the status of the transaction and then
read MMC_RES FIFO. If a response time-out occurred, the MMC_RES FIFO will not contain any

valid data.

15.4.5

Erase

An erase command is performed as described in

Section 15.4.4

with the following additions: the

BUSY_BIT in the MMC_CMDAT register must be set to a 1 after it reads the MMC_RES FIFO.

15.4.6

Single Data Block Write

In a single block write command, the software must stop the clock and set the registers as described

in

Section 15.4.4

. These registers must be set before the clock is started:

•

Set MMC_NOB register to 0x0001.

•

Set MMC_BLKLEN to the number of bytes per block.

«
...
520
521
522
523
524
...
»

Summary of Contents for PXA255

























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXA255

Brand: TC Electronic Pages: 55

Brand: GAMDIAS Pages: 15

Brand: ESD Pages: 28

Brand: Lanner Pages: 63

Brand: Z Microsystems Pages: 51

Brand: Baicells Pages: 10

Brand: ZALMAN Pages: 7

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Brand: Intel Pages: 112

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Acme Packet 3900

Brand: Oracle Pages: 70

Brand: Amphenol Pages: 43

Broadband 700 MHz

Brand: Alcatel-Lucent Pages: 8

Brand: Radio Shack Pages: 154

Brand: ST Pages: 64

Brand: c Pages: 32

Brand: Jäger Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands