InnoMedia MTA 3328-2R User Manual Download

Page: 66 / 84

InnoMedia MTA 3328-2R User’s Guide – Chapter 4

page allows the user to enter their PC’s MAC address
in the router (built into the MTA 3328-2R), to
successfully authenticate into the service provider.

Configure MAC Address Cloning Information Page

This page displays the following information:

Enable MAC Address Cloning

– when this

checkbox has an “x,” the MAC address cloning
feature is enabled (the default is disabled); to
enable, click the checkbox so an “x” appears.

Cloning MAC Address

– when MAC address

cloning is enabled, this field contains the PC’s
MAC address to allow successful
authentication into the service provider.

To configure MAC Cloning settings, refer to the

Using

MAC Cloning

section on page 30 in this Guide.

PPPoE Setting

This page allows you to define PPPoE settings, based
on your service provider’s information.

Summary of Contents for MTA 3328-2R





















































































Search results

Summary of Contents for MTA 3328-2R

Reviews:

Related manuals for MTA 3328-2R

Brands by name

Popular brands

InnoMedia MTA 3328-2R, User Manual

Search results

Summary of Contents for MTA 3328-2R

Reviews:

Related manuals for MTA 3328-2R

Brands by name

Popular brands