InnoMedia MTA 3328-2R User Manual Download

Page: 47 / 84

InnoMedia MTA 3328-2R User’s Guide – Chapter 4

Web Management Tool Home Page

Configuring the MTA 3328-2R via
the Web Management Tool

On the left-hand side of the page, there are seven (7)
sidebar menu items:

Network Configuration

Port Configuration

Device Management

Advanced Settings

Router Settings

Reboot

Restore Default Values

The sections below describe each menu item and the
settings available on each page.

Network Configuration

In the Web Management tool, click the

Network

Configuration

link on the sidebar menu on the left-

hand side of the page.

The Network Configuration page displays the number
that uniquely identifies the device (MAC Address),
along with the IP settings that allow the device to
connect to the Internet.

Summary of Contents for MTA 3328-2R





















































































Search results

Summary of Contents for MTA 3328-2R

Reviews:

Related manuals for MTA 3328-2R

Brands by name

Popular brands

InnoMedia MTA 3328-2R, User Manual

Search results

Summary of Contents for MTA 3328-2R

Reviews:

Related manuals for MTA 3328-2R

Brands by name

Popular brands