manualshive.com logo in svg

Innomed Medical HeartScreen112 Clinic, User Manual

Share
Download
Innomed Medical HeartScreen112 Clinic User Manual Download Page 26

HS112 C-1 User Manual 

26/73 

R-6730-EN02-E 

 

 

 

8.11. Controlling direct online printing 

Online printing can be started by pressing the 

  button while the device is in monitoring 

mode.  Printing  will  be  initialized  with  the  settings  corresponding  to  those  displayed  on  the 
screen (number of leads, lead group, sensitivity, sweep speed). 

 

Attention! 

If there is a limb lead attachment error when online printing is initialized, printing will not start, 
and a “Check the electrodes” notification will appear. 

If the ECG signal is too noisy during printing (black paper is printed), printing will stop after a 
few seconds. 

 

 

Stopping the printing: 

Pressing the 

  button again (or pressing the 

  button) displays a “

PreStop

” message 

on the top left corner of the display. This signals that the device has registered the command  
to stop printing, and that it will stop printing at the end of the current page. If the user wishes 

to  print  a single-page ECG record,  the  

  button can be pressed immediately after the 

printing has begun, and this will stop the printing when the end of the page is reached. If the 

user wishes to print a two-page record, the 

 button can be pressed at any time while the 

second page is being printed. The same system applies for any number of pages. 
This method is useful for good paper utilization. 

If the 

  button is been pressed towards the end of the page, the printing might continue 

until  the  end  of  the  following  page.  Therefore,  it  is  advised  to  stop  the  printing  as  soon  as 
possible after the final desired page starts printing. 
To stop printing before the end of the page is reached  (e.g. in  case of a  low sweep speed), 

press the 

 button one more time after the ”

PreStop

” notification appears. The device will 

immediately stop printing and roll the paper out until the page boundary. 
Even if it is not stopped manually, online printing will stop when a technical limit is reached – 
–

 

depending  on  the  number  of  leads  being  printed,  paper  speed,  ECG  signal.  This  can 

especially be the case with 50 mm/s printing. 

 

Attention! 

After pressing the 

   

or 

 

button, printing may start with a 1–2 second delay. A message (e.g. 

“Printing: 12ch”) appearing at the top left corner of the screen signals that printing will start soon. 
The number represents the number of channels to be printed. 

 

After printing is complete, the device rolls the paper out until the beginning of the next page. 

Summary of Contents for HeartScreen112 Clinic










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands