manualshive.com logo in svg

INIM Electronics SmartLine Series, Installation And Programming Manual

Share
Download
INIM Electronics SmartLine Series Installation And Programming Manual Download Page 8

8

General information

Conventional fire detection control panel

Chapter 2

General information

2.1

Supplied documentation

• Installation and programming manual (this manual)

• User's manual

The Installation manual is inside the device package. For further copies of the Installation Manual, please

contact INIM electronics offices.

2.2

Manual details

• Title: SmartLine installation and programming manual

• Version: 3.60

• Manual code: DCMIINE0SLINE

• Addresses: installer, technicians

2.3

Operator qualifications - access levels

The SmartLine is EN-54 compliant. There are four access levels:

Level 1:

The Public 

All persons in the building can view the system status (active events) and events log; silence

the panel beeper and, under pre-alarm conditions, override pre-alarm status and activate an

instant alarm.

Level 2:

Authorized operators — person/s responsible for the safety of the building and its occupants.

Authorized operators (keyswitch and PIN users) can silence the outputs, reset the panel,

activate the 'Investigation' delay, disable zones, points and outputs, change the operating mode

(Day/Night) and activate the 'Evacuation' alarm.

Level 3:

Authorized technicians appointed by the Installer company.

Such technicians possess the tools required for the removal of the control panel frontplate. And,

are allowed to insert the jumper which enables the control panel programming phase (via

control panel or PC), in order to access the programming and maintenance functions. The

control panel is unable to process data or generate fault or alarm signals of any kind during the

programming phase. 

Level 4:

 Technicians employed by the Manufacturer (INIM Electronics s.r.l.).

The manufacturer company technicians can, by means of special tools, repair or replace the

control panel components.

Note:

This manual is for Authorized installer company technicians (Level 3). However, it also provides some
installation information related to level 1 and level 2.

2.4

Intellectual property rights

The information contained in this document is private property. All rights reserved.

This document must not be reproduced, either totally or in part, without the prior written consent of INIM

Electronics, and refers to the devices specified in 

paragraph 2.12

.

2.5

Disclaimer

INIM Electronics s.r.l. shall not be responsible for damage arising from improper application or use.

This control panel should be handled by qualified personnel only. Installation must be carried out strictly in

accordance with the instructions described in this manual, and in compliance with the local fire code in force.

Summary of Contents for SmartLine Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands