manualshive.com logo in svg

INIM Electronics SmartLine Series, Installation And Programming Manual

Share
Download
INIM Electronics SmartLine Series Installation And Programming Manual Download Page 57

Installation and programming manual

Programming the extinguishant board

57

Chapter 11

Programming the extinguishant board

The extinguishant board manages a gas extinguishant system activated by automatic or manual commands:

• automatic commands triggered by the fire-control panel when the programmed zones go into alarm status.

• manual commands from devices connected to the extinguishant-board inputs or set up as fire-detection loop 

input points.

Therefore, the board makes use of its own terminals and those of the control panel zones, in order to

obtain the activation conditions and command the outputs:

Figure 36 - Extinguishant board: operating principles

NO

NO

Automatic

Activation

Automatic

Pre-Extinguish

Time

Automatic Pre-Extinguish

Time NOT Expired

Stand By

ACTIVATION

Stop?

NO

YES

Manual

Activation

Input

STOP-EXT

STOP-EXT

EXTINGUISH

Manual

Pre-Extinguish

Time

Manual Pre-Extinguish

Time NOT Expired

Pre-Extinguish

Time Expired

Wait for

RESET

Activated

until

Reset

NO

Extinguish

Time

YES

PS

activated

?

YES

MAX 3

Discharge attempts

Extinguish

Confirmed

?

Input

Restored

?

YES

NO

Summary of Contents for SmartLine Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands