manualshive.com logo in svg

INIM Electronics SmartLine Series, Installation And Programming Manual

Share
Download
INIM Electronics SmartLine Series Installation And Programming Manual Download Page 68

68

Iris devices

Conventional fire detection control panel

Appendix A

Iris devices

All Enea series devices manufactured by INIM Electronics for

addressable-analogue detection are LPCB certified and carry the CE

mark in compliance with the CPD standard.

The operating parameters of detectors may be modified to suit their specific environments and, when used

in conjunction with the EITK-DRV supplied by INIM Electronics. This device allows you to connect directly to

the detector line for a complete diagnosis of each detector and thus test its operating capacity, verify its

real-time values, view the contamination level in the optical smoke chamber and change its sensitivity and

operating mode. Each detector has a non-volatile memory which allows you to view the smoke and

temperature levels measured in the period prior to the last alarm detected.

The Iris series of INIM Electronics provides three conventional detector models:

• Optical chamber with sealed upper-part and 500 micron hole-diameter mesh insect screen

• Bicolour LED: red for alarm, green blinking for standby or for trouble

• Drift compensation for sensor drift caused by dust in the chamber

• Sensitivity selection for smoke and heat thresholds

• Operating mode selection (for ID300 version): only smoke, only heat

• AND mode, OR mode, PLUS mode

• Complete diagnostics -  provides contamination level and real-time values

• Memory of the smoke and temperature levels measured in the five-minute period prior to the last alarm 

detected

• Bypass plate on base guarantees line continuity in the event of removal of the detector

For further details regarding the precise features and technical specification of each device, refer to the

respective instructions booklet.

Type

Model

Description

Detectors

ID100 

Optic smoke detector

ID200

Heat detector

ID300

Smoke and heat detector

Bases

EB0010

Mounting base

EB0020

Relay base

ESB010

Sounder base (to be installed under EB0010 mounting base with 
a dedicated wiring)

ESB020

Sounder base and beacon (these are to be installed under 
EB0010 base and require dedicated wiring)

Manual call 
points

IC0010

Manual call point

IC0010E

Manual call point for outdoor installation (IP67)

Alarm repeater FI100

Remote addressable alarm repeater

Driver

EITK1000

Kit for the configuration, maintenance and diagnostics of systems 
using IRIS and ENEA series devices

EITK-DRV

Driver for zones with IRIS series devices or loops with ENEA 
series devices

EITK-BASE

Base for the connection of IRIS and ENEA series detectors

EITK-PWSP

Power supply for the EITK-DRV driver

Summary of Contents for SmartLine Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands