IHIMER 9VXE Original Instructions Manual Download Page 92

Page: 92 / 118

MAINTENANCE

9VXE EN

3-23

WB-C310290

WC-C300400

Replace Filter Element

1. Stop the engine.

2. Turn the fuel cock (1) to the "Close" position to cut off

fuel.

Fuel may flow out if the cup (3) is removed without
turning the fuel cock to the "Close" position.

3. Turn the retainer ring (2) counterclockwise and remove

the cup. Pull down the element (4) to detach it.

4. Clean the inside of the cup.

5. Attach a new element and O-ring (5) to the body.

Replace the O-ring if it is damaged.

6. Turn the retainer ring clockwise and attach the cup.

Tighten the ring by hand.

7. Open the fuel cock as before.

8. Discharge air when the fuel filter is replaced.

9. Make sure that no fuel leaks.

How To Discharge Air

Discharge air after maintenance of the fuel filter or water

separator is carried out or the fuel tank is emptied.

1. Fill the fuel tank full with fuel.

2. Turn the engine key switch to the ON position and

keep it at that position for approximately 20 seconds.

3. The automatic air discharging device discharges air

automatically. The engine can be started.

•

Fuel is hot immediately after stopping the

engine. Carry out the work after the fuel
temperature has become lower.

•

Do not bring fire close to the engine.

•

Wipe off spilt fuel completely. If it is left as is, it

may cause a fire.

Fuel filter

Water separator

Fuel filter

Close

Open

Summary of Contents for 9VXE























































































































Search results

Summary of Contents for 9VXE

Reviews:

Related manuals for 9VXE

Brands by name

Popular brands

IHIMER 9VXE, Original Instructions Manual

Search results

Summary of Contents for 9VXE

Reviews:

Related manuals for 9VXE

Brands by name

Popular brands