IHIMER 9VXE Original Instructions Manual Download Page 91

Page: 91 / 118

MAINTENANCE

9VXE EN

3-22

WB-C310290

WC-C300380

WC-C300391

Check and Clean Water Separator and Replace Element

If the float (1) of the water separator is floating, water
reaches the bottom of the float.
Discharge water if the float reaches the element (2).
1. Stop the engine.

2. Close the fuel cock (3).

3. Turn the retainer ring (4) counterclockwise and

remove the cup (5).

4. Take out the float and spring (6) from inside of the cup.

5. Discharge water and sediment from inside of the cup

into the container.

6. Put the float and spring in the cup.

7. Turn the retainer ring clockwise and attach the cup.

Tighten the ring by hand.

8. Open the fuel cock as before.

9. Discharge air from the water separator.

10. Make sure that no fuel leaks.

Cleaning and Replacing

1. Stop the engine.

2. Close the fuel cock.

3. Turn the retainer ring counterclockwise and detach the

cup.

4. Take out the float and spring from inside of the cup.

5. Discharge water and sediment from inside of the cup

into the container.

6. Clean the element and inside of the cup completely

with fresh fuel. Replace the element if it is flawed or
damaged.

7. Attach the element and O-ring to the body.

8. Put the float and spring in the cup.

9. Turn the retainer ring clockwise and attach the cup.

Tighten the ring by hand.

10. Open the fuel cock as before.

11. Discharge air from the water separator.

12. Make sure that no fuel leaks.

•

Fuel is hot immediately after stopping the engine. Carry out the work after the fuel

temperature has become lower.

•

Do not bring fire close to the engine.

•

Wipe off spilt fuel completely. If it is left as is, it may cause a fire.

Fuel filter

Water separator

Close

Open

Water separator

Summary of Contents for 9VXE























































































































Search results

Summary of Contents for 9VXE

Reviews:

Related manuals for 9VXE

Brands by name

Popular brands

IHIMER 9VXE, Original Instructions Manual

Search results

Summary of Contents for 9VXE

Reviews:

Related manuals for 9VXE

Brands by name

Popular brands