IHIMER 9VXE Original Instructions Manual Download Page 50

Page: 50 / 118

OPERATION

9VXE ENG

2-22

Changing Direction

Turning during traveling

Return the travel lever toward the neutral position a little

to change the direction during forward (or backward)

traveling.

When the lever of the intended turning direction is

returned a little, the machine turns slowly in that direction.

Pivot turning (when blade is in front of machine)

Drive a single crawler to change the direction.

1. Pivot

turn

the

left

Push the right travel lever (1) to turn the machine

forward. Pull it back to turn the machine backward.

2. Pivot turn to the right. Use the left travel lever (2) in the

same way.

Spin turning (when blade is in front of machine)

Drive the right and left crawlers in the reverse directions

to change the direction without traveling the machine.

1. Spin turning to the left.

Push the right travel lever forward and pull back the left

lever.

2. Spin turning to the right.

Pull back the right travel lever and push the left lever

forward.

Forward
turning to left

Backward
turning to right

Pivot turn to left

WB-C210410

Forward turning
to right

Backward
turning to left

Pivot turn to right

WB-C210420

Spin turning

WB-C210430

Summary of Contents for 9VXE























































































































Search results

Summary of Contents for 9VXE

Reviews:

Related manuals for 9VXE

Brands by name

Popular brands

IHIMER 9VXE, Original Instructions Manual

Search results

Summary of Contents for 9VXE

Reviews:

Related manuals for 9VXE

Brands by name

Popular brands