IFM Electronic LR2059 Operating Instructions Manual Download

Page: 3 / 51

7.4.2 Installation of the coaxial pipe ............................................................21

7.5 Probe length ...............................................................................................22

7.5.1 Shorten the probe ...............................................................................22

7.5.2 Determine probe length L for single probes........................................23

7.5.3 Shortening of the coaxial pipe ............................................................23

7.5.4 Determine probe length L for coaxial probes ......................................24

7.6 Installation of the unit with single probe .......................................................24

7.6.1 Installation to G¾ process connection directly in the tank lid .............25

7.6.2 Installation in the tank lid using a G¾ flange plate .............................25

7.6.3 Installation in open metal tanks ..........................................................26

7.6.4 Installation in plastic tanks ..................................................................27

7.7 Installation of the unit with coaxial probe .....................................................28

7.8 Alignment of the sensor housing .................................................................28

8 Electrical connection ..........................................................................................29
9 Operating and display elements ........................................................................30
10 Menu ................................................................................................................31

10.1 Menu structure ...........................................................................................31

10.2 Explanation of the menu ............................................................................33

10.2.1 Main menu [I] ....................................................................................33

10.2.2 EF level (extended functions) [II] ......................................................33

10.2.3 CFG level (configuration) [III] ............................................................34

10.2.4 ENV level (environment) [IV] ............................................................34

10.2.5 SIM level (simulation) [V] ..................................................................34

11 Parameter setting .............................................................................................35

11.1 Parameter setting in general ......................................................................35

11.2 Basic settings (set-up) ...............................................................................37

11.2.1 Enter type of probe used ..................................................................37

11.2.2 Enter probe length ............................................................................37

11.2.3 Set to the medium .............................................................................38

11.2.4 Carry out tank adjustment .................................................................38

11.3 Configure display (optional) .......................................................................39

11.4 Set output signals ......................................................................................39

11.4.1 Set output function for OUT 1 ...........................................................39

11.4.2 Set switching limits (hysteresis function) ..........................................39

11.4.3 Set switching limits (window function) ..............................................39

11.4.4 Set switch-on delay for switching outputs .........................................40

Summary of Contents for LR2059




















































Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands

IFM Electronic LR2059, Operating Instructions Manual

Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands