IFM Electronic LR2059 Operating Instructions Manual Download

Page: 38 / 51

11.2.3 Set to the medium

► Select [MEdI] and set:

[HIGH] = For water and water-based media

Operating mode is optimised for suppression of deposits on the

probe.

[MId] =

For water-based media and media with a medium dielectric

constant value, e.g. oil-in-water emulsions.
Operating mode optimised for the detection of media with

increased foam build-up.

[LOW] = For oils and oil-based media

Note: Option only visible if [Prob] = [COAx].

►

Press [Enter].

►

Check proper function by an application test.

Then the unit changes to the operating mode.
If required (e.g. when mounted in a connection piece), carry out a tank adjustment

(parameter [tREF]) and set parameters to adapt to the application.

Setting ranges of all parameters: (→ 13.1)
Factory settings of all parameters: (→ 15)

11.2.4 Carry out tank adjustment

Menu item only visible if [LEnG] ≥ 260 mm and [Prob] = [rod].

►

Observe notes

(→ 7.2.7)

►

Select [tREF].

►

Press [Enter].

> [nonE] or the value saved from the last tank adjustment (distance value)

is displayed.

►

Press [

▲

] or [

▼

] for at least 1 s.

The distance value is displayed (default value: 10 mm).

► Correct the value, if necessary, with [▲] oder [

▼

]. Incrementally by

pressing the button once or continuously by keeping the button pressed.

►

Press [Enter].

> [donE] is displayed.

►

Press [Enter] again.

> The unit reboots and then returns to the operating mode.

Summary of Contents for LR2059




















































Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands

IFM Electronic LR2059, Operating Instructions Manual

Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands