IFM Electronic LR2059 Operating Instructions Manual Download

Page: 44 / 51

12 Operation

12.1 Operation with single probe

The single probe is made up of one individual rod. Operation with a single probe is

suited for the detection of aqueous media, in particular of heavily soiled aqueous

media.

For correct function with single probe, the unit needs a sufficiently large

metal launching surface / launching plate. It is necessary for transferring

the microwave pulse to the tank with optimum transmission power.
For installation in closed metal tanks / metal bypass pipes, the tank lid

/ upper pipe section serves as a launching surface. For installation in

open metal tanks, tanks made of plastic or metal tanks with plastic lids

a sufficiently large fixing plate, a metal plate or similar must be used

(→

7.6.3),

(→ 7.6.4)

For operation with single probe, minimum distances to tank walls and

structures in the tank must be adhered to

(→ 7.2)

12.2 Operation with coaxial probe

The coaxial probe is made up of an inner probe and an outer probe pipe (coaxial

pipe). The probe is centred in the coaxial pipe by one or several spacers.
In case of operation with a coaxial probe media with a low dielectric constant (e.g.

oil and oil-based media) are detected in addition to aqueous media.

In addition, the following applies in case of operation with coaxial probe:

• No launching plate is required.
• No minimum distances to tank walls and objects in the tank need to be

observed.

• No tank adjustment is necessary.

Observe the application area of the coaxial probe

(→ 5.2)

12.3 Function check

After power-on the device is in the operating mode. It carries out its measurement

and evaluation functions and generates output signals according to the set

parameters.

►

Check whether the unit operates correctly.

Summary of Contents for LR2059




















































Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands

IFM Electronic LR2059, Operating Instructions Manual

Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands