IFM Electronic LR2059 Operating Instructions Manual Download

Page: 9 / 51

6.2 Outputs

The unit generates output signals according to the parameter setting. 2 outputs

are available. They can be set separately.

OUT1

switching signal for level limit / IO-Link

(→ 6.3.7)

OUT2

• analogue signal proportional to level 4...20 mA / 20...4 mA

• switching signal for level limit

6.3 Other features of the unit

•

Increased temperature range, increased protection rating (→ Technical data

sheet)

• Special operating mode for media with increased foam build-up

(→ 11.2.3)

• Tank adjustment enables suppression of undesired interference

(e.g. caused by structures in the tank or when mounted in a connection piece

(→ 11.2.4)

)

• Display of the level and the switching status via display / LEDs
• IO-Link function

(→ 6.3.7)

6.3.1 Display functions

The unit displays the current level, either in mm or in percent of the scaled

measuring range. Factory setting: mm.

The display unit is defined by programming

(→ 11.3)

In the operating mode, the user can temporarily switch between the length display

(mm) and percentage

(→ 12.6)

The set unit of measurement and the switching status of the outputs are indicated

by LEDs

(→ 9)

Summary of Contents for LR2059




















































Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands

IFM Electronic LR2059, Operating Instructions Manual

Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands