IFM Electronic LR2059 Operating Instructions Manual Download | Manualshive

Page: 14 / 51

background image

14

6.3.7 IO-Link

This unit has an IO-Link communication interface which requires an IO-Link

capable module (IO-Link master) for operation.
The IO-Link interface enables direct access to the process and diagnostic data

and provides the possibility to set the parameters of the unit during operation.
In addition, communication is possible via a point-to-point connection with a USB

IO-Link master.
The IODDs necessary for the configuration of the unit, detailed information about

process data structure, diagnostic information, parameter addresses and the

necessary information about required IO-Link hardware and software can be

found at www.ifm.com.

6.3.8 Simulation functions

Various levels and errors can be simulated for set-up, maintenance or interference

reduction. The duration of the simulation can be selected (1 min...1 h). The

simulation can be started manually and runs until it is stopped manually or the

set time elapses. During the simulation the outputs respond according to the

simulated process values

.

7 Installation

7.1 Installation location / environment

• Vertical installation from the top is preferred.

7.2 Unit with single probe

►

Observe the notes on tank adjustment

• For installation in open tanks

• For installation in plastic tanks

«
...
12
13
14
15
16
...
»

Summary of Contents for LR2059




















































Reviews:

No comments

Related manuals for LR2059

Brand: Back View Pages: 168

Brand: Darfon Pages: 28

Brand: VanEssa mobilcamping Pages: 8

Action Replay DSi

Brand: Datel Pages: 2

Brand: YOKOGAWA Pages: 12

Brand: BAFANG Pages: 4

Brand: Fronius Pages: 56

Brand: Hyena Pages: 13

Brand: Kolpin Pages: 25

Brand: BGS technic Pages: 5

Brand: PCB Piezotronics Pages: 7

Baby Go Round Twirl

Brand: Redkite Pages: 4

Brand: Mystic Romance Pages: 10

Alarm Clock Camera Case

Brand: Wasserstein Pages: 10

Brand: Takex Pages: 20

The Professional

Brand: SLIK Pages: 2

Brand: QualGear Pages: 6

Brand: AC Schnitzer Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands