IFM Electronic LR2059 Operating Instructions Manual Download | Manualshive

Page: 24 / 51

background image

24

7.5.4 Determine probe length L for coaxial probes

►

Measure the exact total length L

K

of the coaxial pipe (Fig. 7-9, on the right).

► Deduct 9 mm from the total length of the coaxial pipe: L

K

– 9 mm = L.

►

Note down L. It is needed for setting the device parameters

7.6 Installation of the unit with single probe

Before installing and removing the unit: Make sure that no pressure is

applied to the system and that there is no medium in the tank that could

leak. Also always take into account the potential dangers related to extreme

machine and medium temperatures.

For installation in closed metal tanks, the tank lid serves as a launching plate R

(Fig. 7-10, Fig. 7-12). Notes

Options are as follows:

• Installation to G¾ process connection directly in the tank lid

• Installation in the tank lid using a flange plate (e.g. for tanks with thin walls)

During installation of the process connection on the tank lid observe the

subsequent orientation of the housing (display orientation, cable outlet).

The sensor housing cannot be rotated with respect to the internal thread!

Subsequent alignment of the sensor housing is therefore not possible.

Furthermore, installation in open tanks

and plastic tanks is

possible

.

«
...
22
23
24
25
26
...
»

Summary of Contents for LR2059




















































Reviews:

No comments

Related manuals for LR2059

Brand: Falltech Pages: 13

Brand: FALK Pages: 41

Brand: quadient Pages: 2

AcousticDesign AD-S52

Brand: QSC Pages: 4

Brand: Saab Pages: 10

AERASGARD RCO2-W

Brand: S+S Regeltechnik Pages: 7

FireCracker CK17A

Brand: X10 Pages: 1

Brand: Waycon Pages: 8

Brand: Wavetronix Pages: 4

Brand: X10 Pages: 2

Brand: EUROM Pages: 28

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: Takex Pages: 4

Brand: Lincoln Electric Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands