IFM Electronic LR2059 Operating Instructions Manual Download

Page: 48 / 51

The setting ranges for analogue start point [ASP2] and analogue end point [AEP2]

depend on the probe length (L). In general the following applies:

min

max

[ASP2]

---

[AEP2]

---

L - 30

Step increment

• Minimum distance between [ASP2] and [AEP2] = 20 % of the active zone.

14 Maintenance / transport

►

Keep the process connection free of deposits and foreign bodies.

Heavy soiling:

►

Clean process connection and probe.

In case of longer operation separation layers can form in the medium (e.g. oil on

water). This applies especially to still pipes or bypasses:

►

Remove separation layers at regular intervals.

In case of operation with coaxial probe:

►

Ensure that the vent hole (at the upper end of the coaxial pipe) remains free.

►

Keep the interior of the coaxial pipe free from foreign bodies and soiling.

When the medium is changed, it may also be necessary to adapt the unit

settings

(→ 11.2.3)

Only if data storage is required in an IO-Link application:

The tank adjustment is not saved via IO-Link. After a replacement it must

be carried out again

(→ 11.2.4)

More information about data storage: (→ 16.2)

►

It is not possible to repair the unit.

►

After use dispose of the unit in an environmentally friendly way in accordance

with the applicable national regulations.

►

In case of returns ensure that the unit is free from soiling, especially dangerous

and toxic substances.

►

For transport only use appropriate packaging to avoid damage of the unit.

Summary of Contents for LR2059




















































Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands

IFM Electronic LR2059, Operating Instructions Manual

Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands