IFM Electronic LR2059 Operating Instructions Manual Download | Manualshive

Page: 22 / 51

background image

22

7.5 Probe length
7.5.1 Shorten the probe

The probe can be shortened to adapt to different tank heights.

Ensure that the probe length is not below the minimum permissible probe

length (Lmin) of 150 mm. The unit does not support probe lengths below

150 mm.
For probe lengths < 260 mm no tank adjustment is possible

Proceed as follows:

►

Screw the probe to the unit.

►

Mark the desired length (L) on the probe. The

reference point is the lower edge of the process

connection (Fig. 7-8).

►

Remove the probe from the unit.

►

Shorten the probe at the mark.

►

Remove all burrs and sharp edges.

►

Screw the probe to the unit again and tighten it

Fig. 7-8

L

min

L

L

min

= 150 mm

«
...
20
21
22
23
24
...
»

Summary of Contents for LR2059




















































Reviews:

No comments

Related manuals for LR2059

Brand: DAPU Pages: 4

Brand: Camtree Pages: 2

Brand: Camtree Pages: 11

Brand: Camtree Pages: 4

Brand: GARO Pages: 23

Brand: IDEAL Pages: 6

Brand: IdeaFly Pages: 3

Brand: Vega Pages: 36

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Waeco Pages: 168

BOS R254K-UUI-PR10-S4

Brand: Balluff Pages: 74

Brand: Hama Pages: 2

Z-MACHINE ZM-KM870R

Brand: ZALMAN Pages: 2

Brand: QualGear Pages: 6

Brand: AC Schnitzer Pages: 16

Brand: Honda Pages: 4

SAFESTOP SS0005

Brand: Pro-gard Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands