IFM Electronic LR2059 Operating Instructions Manual Download

Page: 35 / 51

11 Parameter setting

During parameter setting the device remains in the operating mode. It continues

to monitor with the existing parameters until the parameter setting has been

completed.

11.1 Parameter setting in general

Select parameter

►

Press [Enter] to get to the menu.

►

Press [

▲

] or [

▼

] until the required

parameter is displayed.

Set parameter value

►

Press [Enter] to edit the selected

parameter.

►

Press [

▲

] or [

▼

] for at least 1 s.

After 1 s: Setting value is changed:

incrementally by pressing the button

once or continuously by keeping the

button pressed.

Numerical values are incremented continuously with [

▲

] or decremented with [

▼

Acknowledge parameter value

►

Press [Enter].

> The parameter is displayed again.

The new setting value is saved.

Set other parameters

►

Press [

▲

] or [

▼

] until the required parameter is displayed.

Finish parameter setting

►

Press [

▲

] or [

▼

] several times until the current measured value is displayed or wait for

30 s.

> The unit returns to the process value display.

[C.Loc] or [S.Loc] as operation indication see

(→ 12.7)

Summary of Contents for LR2059




















































Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands

IFM Electronic LR2059, Operating Instructions Manual

Search results

Summary of Contents for LR2059

Reviews:

Related manuals for LR2059

Brands by name

Popular brands