IFM Electronic LR2059 Operating Instructions Manual Download | Manualshive

Page: 21 / 51

background image

21

UK

7.4.2 Installation of the coaxial pipe

This subchapter is only relevant if the unit is to be operated with a coaxial probe.

The coaxial pipe and the probe must be of the same length. The coaxial

pipe can be shortened

.

►

Slide the supplied flat seal (A) onto the thread.

The elastomer seal may remain on the unit.

►

Slide the coaxial pipe (B) onto the probe.

Carefully centre it and carefully move the

probe through the centring piece (C) - for

lengths > 1400 mm through both centring

pieces - of the coaxial pipe. Do not damage

the centring pieces.

►

Screw onto the sensor thread and tighten.

Recommended tightening torque: 35 Nm.

A

C

B

34

32

«
...
19
20
21
22
23
...
»

Summary of Contents for LR2059




















































Reviews:

No comments

Related manuals for LR2059

Brand: IBS Pages: 24

Brand: Panasonic Pages: 1

Brand: JANE Pages: 6

Brand: AAMP of America Pages: 6

Brand: zenitech Pages: 16

Brand: Oki Pages: 4

Brand: JANE Pages: 21

Brand: Trace2O Pages: 9

IMI SENSORS EX640B61

Brand: PCB Piezotronics Pages: 70

Brand: Anslut Pages: 12

Brand: Metra Electronics Pages: 2

Brand: Southern Enterprises Pages: 4

Brand: Ohlins Pages: 8

Brand: Metric Halo Pages: 21

IO-Link BAE SA-CS-027-YI-BP00,3 GS04

Brand: Balluff Pages: 50

Brand: AZZA Pages: 18

Brand: Cargo Floor Pages: 16

Brand: Filmcity Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands