IEI Technology PCISA-LX User Manual Download Page 82

Page: 82 / 214

Page 82

IEI® Technology, Corp

PCISA-LX CPU Card

Figure 4-2: Connection of IDE Connector

NOTE:

When two EIDE disk drives are connected together, back-end

jumpers on the drives must be used to configure one drive as

a master and the other as a slave.

4.8.2 COM2-COM3 RS-232 Serial Port Installation

The cable used to connect the CPU card to an RS-232 serial port is a 10-pin header to

male D-sub 9 connector. To connect an RS-232 serial port to the CPU card, follow the

instructions below.

Step 1:

Step 2:

Step 3:

Find the RS-232 cable in the kit that came with the CPU card.

Connect the 10-pin connector end of the cables to the COM2 /COM3 box

headers on the CPU card. Be sure to align the red wire on the connector to pin 1

on the box header.

Connect the other end of the cables to standard female D-sub 9 connectors.

Step 0:

Summary of Contents for PCISA-LX























































































































































































































Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands

IEI Technology PCISA-LX, User Manual

Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands