IEI Technology PCISA-LX User Manual Download Page 117

Page: 117 / 214

Page 117

PCISA -LX CPU Card

Auto

EFAULT

The computer selects the correct mode.

Mode 0

PIO mode 0 selected with a maximum transfer rate of 3.3MBps.

Mode 1

PIO mode 1 selected with a maximum transfer rate of 5.2MBps.

Mode 2

PIO mode 2 selected with a maximum transfer rate of 8.3MBps.

Mode 3

PIO mode 3 selected with a maximum transfer rate of 11.1MBps.

Mode 4

PIO mode 4 selected with a maximum transfer rate of 16.6MBps.

IDE UDMA [Auto]

Use the

IDE UDMA

option below to select the Ultra DMA (UDMA) mode for the following

HDDs:

IDE Primary Master UDMA

IDE Primary Slave UDMA

Auto

EFAULT

The computer selects the correct UDMA.

Disabled

The UDMA for the HDD device is disabled.

IDE DMA transfer access [Enabled]

Use the

IDE DMA transfer access

option to enable or disable DMA support for IDE

devices connected to the system.

Disabled

All IDE drive DMA transfers are disabled. The IDE drives

use PIO mode transfers.

Enabled

EFAULT

All IDE drive DMA transfers are enabled.

IT8888 ISA Decode IO [Press Enter]

Press Enter to open the

IT8888 ISA Decode I/O

menu. The

IT8888 ISA Decode I/O

options are shown in

Section 0

Summary of Contents for PCISA-LX























































































































































































































Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands

IEI Technology PCISA-LX, User Manual

Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands