IEI Technology PCISA-LX User Manual Download Page 31

Page: 31 / 214

Page 31

PCISA -LX CPU Card

2.10 Ethernet

The Realtek RTL8100C is a single-chip Fast Ethernet controller. It is enhanced with an

ACPI (Advanced Configuration Power Interface) management function for PCI in order to

provide efficient power management for advanced operating systems with OSPM

(Operating System Directed Power Management). The RTL8100C also supports remote

wake-up (including AMD Magic Packet

™

and Microsoft

Wake-up frame). Realtek

RTL8100C features are listed below.

128-pin PQFP/LQFP

Supports PCI/mini-PCI interfaces

Integrates Fast Ethernet MAC, physical chip, and transceiver onto a single

chip

10Mbps and 100Mbps operation

Supports 10Mbps and 100Mbps N-way auto-negotiation

Supports 25MHz Crystal or 25MHz OSC as the internal clock source

Complies with PC99/PC2001 standards

Supports ACPI power management

Provides PCI bus master data transfer

Provides PCI memory space or I/O space mapped data transfer

Supports PCI clock speed of 16.75MHz-40MHz

Advanced power saving mode

Supports Wake-on-LAN and remote wake-up (AMD Magic Packet

™

, Link

Change, and Microsoft

Wake-up frame)

Half/Full duplex capability

Supports Full Duplex Flow Control (IEEE 802.3x)

Provides interface to 93C46 EEPROM to store resource configuration and ID

parameters

Provides PCI clock run pin

Provides LED pins for network operation status indication

2.5/3.3V power supply with 5V tolerant I/Os

0.25µm CMOS process

Summary of Contents for PCISA-LX























































































































































































































Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands

IEI Technology PCISA-LX, User Manual

Search results

Summary of Contents for PCISA-LX

Reviews:

Brands by name

Popular brands