![background image](http://html1.mh-extra.com/html/icom/ic-i7410/ic-i7410_instruction-manual_4297834103.webp)
96
1
2
3
4
5
6
7
8
9
10
11
14
15
16
18
19
20
21
MAINTENANCE
17
13
12
13
D
Transceiver power
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
Power does not turn ON
when the [POWER] switch is
pushed.
• The power cable is improperly connected.
• A fuse is blown.
• Re-connect the DC power cable correctly.
• Correct the cause, then replace the fuse with
an equivalent fuse.
( Fuses are installed in the DC power cable
and in the internal PA unit.)
p. 19
p. 99
D
Transmit and receive
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
No sound from the speaker.
• The audio volume level is too low.
• The squelch is closed.
• The transceiver is in transmit.
• Rotate the [AF] control clockwise to obtain a
suitable listening level.
• Rotate the [RF/SQL] control to 11 o’clock po
-
sition to open the squelch.
• Push [TRANSMIT] to receive or check the
SEND line of an external unit, if connected.
p. 31
p. 32
p. 34
Sensitivity is too low, and only
strong signals are audible.
• The antenna is not connected properly.
• The antenna for another band is selected.
• The antenna is not properly tuned.
• The attenuator is turned ON.
• Re-connect to the antenna connector.
• Select an antenna suitable for the operating
frequency.
• Hold down [TUNER] for 1 second to manually
tune the antenna.
• Push [P.AMP/ATT] to turn OFF the attenuator.
—
p. 82
p. 83
p. 55
Received audio is unclear or
distorted.
• The operating mode is not matched.
• The Passband Tuning function is turned ON.
• The Noise Blanker function is turned ON when
receiving a strong signal.
• Preamplifier is turned ON.
• The Noise Reduction function is turned ON
and the [NR] control is too far clockwise.
• Select a suitable operating mode.
• Hold down [PBT-CLR] for 1 second to reset
the function.
• Push [NB] to turn OFF the function.
• Push [P.AMP/ATT] once or twice to turn OFF
the function.
• Set the [NR] control for maximum readability.
p. 31
p. 59
p. 60
p. 55
p. 61
[ANT•METER] does not func
-
tion
• The Antenna Switch function is set to “OFF.”
• Set the Antenna Switch function to “Auto” or
“Manual” in the Set mode.
p. 87
Transmitting is impossible.
• The operating frequency is outside the se
-
lected ham band.
• Set the frequency to be within the selected
ham band.
p. 26
Output power is too low.
• The [RF PWR] control is set too far counter
-
clockwise.
• The [MIC] control is set too far counterclock
-
wise.
• The antenna for another band is selected.
• The antenna is not properly tuned.
• Rotate the [RF PWR] control clockwise.
• Set the [MIC] control to a suitable position.
• Select an antenna suitable for the operating
frequency.
• Hold down [TUNER] for 1 second to manually
tune the antenna.
p. 34
p. 34
p. 82
p. 83
No contact can be made with
another station.
• The RIT or
∂
TX function is turned ON.
• The Split function is turned ON.
• Push [RIT] or [
∂
TX] to turn OFF the function.
• Push [SPLIT] to turn OFF the function.
pp. 53, 65
p. 66
Transmit signal is unclear or
distorted.
• The [MIC] control is set too far clockwise.
• Set the [MIC] control to a suitable position.
p. 34
Repeater cannot be accessed.
• The Split function is not turned ON.
• The programmed subaudible tone frequency
is wrong.
• Push [SPLIT] to turn ON the function.
• Reset the frequency using the Set mode.
p. 66
p. 52
■
Troubleshooting
The following chart is designed to help you correct
problems which are not equipment malfunctions.
If you are unable to locate the cause of a problem,
or solve it through the use of this chart, contact your
nearest Icom Dealer or Service Center.