Icom IC-FR3000 Series, Sales Handbook

Page: 45 / 74

3-7 Phone Patch – Transceiver to Phone
The IC-FR3000/FR4000 repeater can be connected
directly to the telephone line.
When a subscriber transmits a DTMF dialing codes, the
repeater, received signal is sent to the telephone line to
connect the phone.
Basic Repeater to Phone Line Connecting System
Basic Repeater to Phone Line Connecting System Basic Repeater to Phone Line Connecting System
Basic Repeater to Phone Line Connecting System
Descriptions Model Number Quantity
UHF Repeater IC-FR4000
UHF Antenna
Duplexer
Telephone Line
System requirement
System requirement System requirement
System requirement
IC-FR4000
UHF H/H
Tx = f
1
Rx = f
2
Tx = f
2
Rx = f
1
Public Telephone Line
DTMF Setting
DTMF Setting DTMF Setting
DTMF Setting
To enable connect phone line functions, the DTMF
settings must be pre-programmed using CS-FR3000
cloning software. Use CS-FR3000 help screens for
description of functions and operation and for
TEL Dial
TEL Dial TEL Dial
TEL Dial (
0015 Default)
①
Enter the programmed password from transceiver.
Code:
∗
0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
45
description of functions and operation and for
programming details.
▒ NOTE
NOTE NOTE
NOTE: Cannot call to phone line from transceiver
▒ when the repeater is working in PMR mode and the
▒ operating channel of 5-Tone format is set to DTMF.
Operation from the transceiver Operation from the transceiver Operation from the transceiver Operation from the transceiver
One of two methods (Dial and Auto-dial) of telephone
access is selectable from the transceiver.
Auto-dial: Using the pre-programmed phone No. (up
to 20 channels are stored) in the repeater.
Dial: Direct dialing from the keypad of a transceiver.
TEL Autodial TEL Autodial TEL Autodial TEL Autodial (
0016 Default)
Autodial number:
12 (Channel 12)
① Enter the following DTMF codes.
Code:
∗
0001#0016#12#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone, de-limiter tone
and command code are correct, and try again.
• The repeater starts calling the autodial channel
12.
②
When the connection has been confirmed, talk to the
phone by simplex voice communication.
③
After conversation is finished enter the password
followed by the “System Control Exit” command to
terminate Phone Patch operation.
Code:
∗
0001#0002#
• Verify the repeater replies “System Control Exit
ACK (2020),” then repeater hangs on the phone.
∗
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make
sure the password, header tone and de-limiter tone
are correct, and try again.
②
Enter the “TEL Dial” command within 10 sec.
Code:
∗
0015#
• Verify the standby time runs out, enter the
password and command continuously (Code:
∗
0001#0015#).
③ Enter the telephone number (if the number is
060-
3355-2244) as sub code within 10 sec.
Code:
∗
06033552244#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter
the password and command continuously (Code:
∗
0001#0015#06033552244#).
• The repeater starts calling the number.
④
When the connection has been confirmed, talk to the
phone by simplex voice communication.
⑤
After conversation is finished enter the password
followed by the “System Control Exit” command to
terminate Phone Patch operation.
Code:
∗
0001#0002#
• Verify the repeater replies “System Control Exit
ACK (2020),” then repeater hangs on the phone.