Icom IC-FR3000 Series, Sales Handbook

Page: 16 / 74

Connector Description
• Pin 4, pin 5, pins 16–18 select one of the 32 pre-programmed memory channels. (see table below)
[0]: Hi-Z, [1]: 0 V (D0–D4: +5 V pull up)
Channel Channel Channel Channel
D4
D4 D4
D4
(pin 18) (pin 18) (pin 18) (pin 18)
D3
D3 D3
D3
(pin 5) (pin 5) (pin 5) (pin 5)
D2
D2 D2
D2
(pin 17) (pin 17) (pin 17) (pin 17)
D1
D1 D1
D1
(pin 4) (pin 4) (pin 4) (pin 4)
D0
D0 D0
D0
(pin16) (pin16) (pin16) (pin16)
Channel Channel Channel Channel
D4
D4 D4
D4
(pin 18) (pin 18) (pin 18) (pin 18)
D3
D3 D3
D3
(pin 5) (pin 5) (pin 5) (pin 5)
D2
D2 D2
D2
(pin 17) (pin 17) (pin 17) (pin 17)
D1
D1 D1
D1
(pin 4) (pin 4) (pin 4) (pin 4)
D0
D0 D0
D0
(pin16) (pin16) (pin16) (pin16)
1 0 0 0 0 0 17 1 0 0 0 0
2 0 0 0 0 1 18 1 0 0 0 1
3 0 0 0 1 0 19 1 0 0 1 0
4 0 0 0 1 1 20 1 0 0 1 1
5 0 0 1 0 0 21 1 0 1 0 0
6 0 0 1 0 1 22 1 0 1 0 1
7 0 0 1 1 0 23 1 0 1 1 0
8 0 0 1 1 1 24 1 0 1 1 1
9 0 1 0 0 0 25 1 1 0 0 0
10 0 1 0 0 1 26 1 1 0 0 1
11 0 1 0 1 0 27 1 1 0 1 0
12 0 1 0 1 1 28 1 1 0 1 1
16
13 0 1 1 0 0 29 1 1 1 0 0
14 0 1 1 0 1 30 1 1 1 0 1
15 0 1 1 1 0 31 1 1 1 1 0
16 0 1 1 1 1 32 1 1 1 1 1
Pin No. Pin No. Pin No. Pin No. Pin Name Pin Name Pin Name Pin Name Description Description Description Description Specification Specification Specification Specification
1 –PTT
Input terminals to transmit the repeater in relation
to the external equipment. An opto-isolator is
provided to facilitate PTT signals.
High voltage=PTT ON (transmits)
Hi-Z=PTT OFF
2 +PTT
3 –AFOUT
Output terminal for AF signals from the AF
detector circuit via the bandpass filter. Output
level is fixed, regardless of [AF] control.
Output impedance: 600 Ω
4 +AFOUT
5 –EXTMOD
Input terminal for the modulation circuit. Input impedance: 600 Ω
6 +EXTMOD
7 –BUSY
Output terminal for squelch condition
(Open/Close). An opto-isolator is provided to
facilitate BUSY signals.
Open collector=BUSY OFF
0 V=BUSY ON (Squelch is opened)
8 +BUSY
Remote connector Remote connector Remote connector Remote connector
*About Remote connector (pins 7, 8) and Accessory connector (pin 1):
*About Remote connector (pins 7, 8) and Accessory connector (pin 1): *About Remote connector (pins 7, 8) and Accessory connector (pin 1):
*About Remote connector (pins 7, 8) and Accessory connector (pin 1):
Depends on the clone setting, BUSY signals are output while receiving a signal
with a matched CTCSS/DCS signal.