background image

75

10

SET MODE

 Set mode (Continued)

Band Edge Beep

A beep sounds when an operating frequency enters or 
exits an amateur band. This function is independent from 
“Beep” (the confirmation beep) setting as above.
on  : Band edge beep ON
oF  : Band edge beep OFF
The volume level can be set in “Beep Level” as below.

ON (default)

Beep Level

This item sets the maximum volume level for the con-
firmation beep and band edge beep tones from 0% to 
100% in 1% steps. 
When beep tones are set to OFF, this setting has no ef-
fect.

50% (default)

Beep Level Limit

Turn the beep tones output level limiting capability ON 
and OFF for the confirmation and band edge beep tones. 
When this item is set to ON, the beep tones are linked to 
the 

[AF]

 control until rotation of the 

[AF]

 control reaches 

to the specified level—further rotation will not increase 
the volume of the beep tones.
on  : Beep level is limited with the 

[AF]

 control

oF  : Beep level is linked to the 

[AF]

 control

ON (default)

RF/SQL Control

The [RF/SQL] control can be set as the RF/squelch con-
trol, the squelch control only (RF gain is fixed at maxi-
mum) or Auto (RF gain control in SSB, CW and RTTY; 
squelch control in AM).
See pgs. 4, 30 for details.
rS (RF+SQL) :  [RF/SQL] control is set as the RF/squelch 

control

Sq (SQL) 

:  [RF/SQL] control is set as the squelch 

control

At (AUTO) 

:  [RF/SQL] control is set as the RF gain 

control in SSB, CW and RTTY; squelch 
control in AM

RF +

 

SQL (default)

Meter Peak Hold

This item turns the meter peak hold function ON or OFF.
on  :  The highest activated segment of the meter remains 

visible for 0.5 sec.

oF  : The meter functions normally.

ON (default)

Summary of Contents for IC-7200









































































































Reviews: