background image

57

6

FUNCTIONS FOR TRANSMIT

 Speech compressor

The IC-7200 has a built-in, low distortion speech com-
pressor circuit. This circuit increases your average talk 
power in SSB mode and is especially useful for DX-
ing or noisy conditions when the receiving station is 
having difficulty copying your signal.

q

  Push 

MODE

 to select an SSB mode.

  •  When SSB mode is selected, push and hold 

MODE

 

for 1 sec. to toggle between USB and LSB modes.

w

  Push 

COMP

 to turn the speech compressor func-

tion ON and OFF.

  •  “

” appears when the speech compressor func-

tion is ON.

MODE

TUNER

TS

FILTER

SPCH

V/M

A/B

SPLIT

M-CL

SCAN

SET

ATT

P.AMP

COMP

VOX

MNF

RIT

1

2

3

4

5

6

7

8

0

50

28

18

14

10

21

24

=

7

3.5

1.8

F-INP

M-CH/RIT

ENT

BAND

GENE

9

.

AGC

MW

ANF

METER

NR

NB

[DIAL]

Appears

COMP

7

21

D

 Compression level setting

• Microphone gain setting

MODE

TUNER

TS

FILTER

SPCH

V/M

A/B

SPLIT

M-CL

SCAN

SET

ATT

P.AMP

COMP

VOX

MNF

RIT

1

2

3

4

5

6

7

8

0

50

28

18

14

10

21

24

=

7

3.5

1.8

F-INP

M-CH/RIT

ENT

BAND

GENE

9

.

AGC

MW

ANF

METER

NR

NB

[DIAL]

[M-CH]

q

  Push 

MODE

 to select an SSB mode.

  •  When SSB mode is selected, push and hold 

MODE

 

for 1 sec. to toggle between USB and LSB modes.

w

  Push 

COMP

 to turn the speech compressor func-

tion OFF, if it’s ON.

  • “

” disappears.

e

  Push and hold 

ANF

METER

 for 1 sec. several times to 

select ALC meter.

  • “

ALC

” appears.

r

 Adjust the MIC gain in the quick set mode.

q

  Push and hold 

M-CH/RIT

SET

 for 1 sec. to enter the 

quick set mode.

w

  Rotate 

[M-CH]

 to select “

MIC GAIN

” to set the 

microphone gain.

e

  While transmitting, speak at a normal voice level 

and rotate 

[DIAL]

 to adjust the microphone gain 

so that the ALC meter reads within the ALC 
zone, whether you speak softly or loudly.

  •  Push and hold 

M-CL

 for 1 sec. to return to the de-

fault value.

r

  Push 

M-CH/RIT

SET

 to exit the quick set mode and 

return to normal operation.

• Compression level setting

q

  Push and hold 

ANF

METER

 for 1 sec. several times to 

select ALC meter.

  • “

ALC

” appears.

w

  Push  and  hold 

COMP

  for  1  sec.  to  enter  the 

speech compression level set mode.

  •  The speech compressor function is turned ON and  

” appears.

 

 You can enter the speech compression level set 
mode before selecting ALC meter in step 

q

.

e

  While transmitting, speak at a normal voice level 

and rotate 

[DIAL]

 to adjust the speech compres-

sion level so that the ALC meter reads within the 
ALC zone, whether you speak softly or loudly.

  •  The speech compression level can be adjusted from 0 

to 10.

  •  Push and hold 

M-CL

 for 1 sec. to return to the default 

value.

Level 5 (default)

ALC zone

r

  Push 

COMP

 to exit the speech compression level 

set mode and return to normal operation.

t

  Push 

COMP

 to turn the speech compressor func-

tion OFF if necessary.

  • “

” disappears.

 

NOTE:

 When the ALC meter peaks above the ALC 

zone, your transmitted voice may be distorted.

Summary of Contents for IC-7200









































































































Reviews: