iColor I Candy 200 User Manual Download Page 70

Page: 70 / 72

User Manual – February 2020 Edition

Print Method:

Thermal inkjet with Uninet

Perfection enhancements

Print Resolutions:

Up to 4800 DPI

Print Speeds:

Draft Mode: 4.5” per second

Normal Mode: 1.8” per second

High Quality Mode: 0.8” per second

Print Head:

Semi-permanent, user-replaceable

Ink Tanks:

Single high capacity Cyan, Magenta, Yellow ink

cartridge; process black

Colors:

16.7 million

Color Matching:

Z-Color™ Color Matching Software

Max. Print Width:

8.25” (209mm)

Media Width:

8.375” (212mm)

Media Types:

Roll-fed pressure-sensitive labels, roll-fed

tags, fan-fold labels or tags

Media Sensing:

Moveable see-through sensor for die-cut labels;

reflective sensor for labels and tags with black

stripe; can use continuous and pre-printed

labels and tags

Supply Roll:

6” (152mm) maximum diameter on 3” (76mm) core

Ink Level Warning:

Calculates actual number of prints remaining

based upon ink usage of graphics being printed

(patent-pending)

Indicator Lights:

Power, Pause, Ink

Controls:

Pause, Feed, Unload

Operating Systems:

Window 7, 8, 10

(Mac Support)

Data Interface: USB 2.0

Label Design Software: Seagull Scientific BarTender

UltraLite Software

Version included; can also be used with most

other popular label design and graphics

programs

Electrical Rating:

12VDC, 5.0A

Power Requirements:

100-240VAC, 50/60 Hz, 60 watts

Certifications:

UL, UL-C, CE, FCC Class B

Weight:

36.5 lbs. (16.6 kg)

Dimensions:

17.25”W x 9.1”H x 17.25”D

(438mmW x 231mmH x 438mmD)

Summary of Contents for I Candy 200









































































Search results

Summary of Contents for I Candy 200

Reviews:

Related manuals for I Candy 200

Brands by name

Popular brands

iColor I Candy 200, User Manual

Search results

Summary of Contents for I Candy 200

Reviews:

Related manuals for I Candy 200

Brands by name

Popular brands