iColor I Candy 200 User Manual Download Page 5

Page: 5 / 72

User Manual – February 2020 Edition

B. Unpacking and inspection

While unpacking your printer, inspect the carton to ensure that no damage has occurred during shipping. Make sure
that all supplied accessories are included with your unit. The following items are included in the supply box:

Power Adapter

Separate Power Cord

6' USB Cable (If other USB cable is used, it must be 6'(2 M) or less.)

ICI200DYE iColor 200 Dye-Based CMY Ink Cartridge

IC200PIG iColor 200 Pigment-Based CMY Ink Cartridge

Warranty Statement and Registration Card

The following items are inside the printer supply roll area:

Starter Roll of High Gloss Label Stock

Save the carton and packing materials. They will come in handy when transporting the printer.

Summary of Contents for I Candy 200









































































Search results

Summary of Contents for I Candy 200

Reviews:

Related manuals for I Candy 200

Brands by name

Popular brands

iColor I Candy 200, User Manual

Search results

Summary of Contents for I Candy 200

Reviews:

Related manuals for I Candy 200

Brands by name

Popular brands