background image

 

 

|  

37

 

User Manual – February 2020 Edition 

F. Creating a full bleed print 

 

1.

 

To create a label that completely fills the space with no white margins, adjust these settings in the status 
monitor and printing application (Seagull Scientific BarTender

®

). 

 

 

Page Size 

Increase the page size width by .03 inches (1mm). Increase the height by .03 inches (1mm). If you are using 
Seagull Scientific BarTender

®

, simply change the size under the File Menu - Page Setup. If you are using other 

graphics programs you will need to change the page size in the application and in the printer driver 
preferences. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Left Margin Offset  

You must decrease the left margin offset to center the over bleed on the label. If you over bleed by .03” you will 
need to decrease the Left Margin Offset by 0.4mm. This will center the page size increase so there is a .03 inch 
over bleed on both left and right sides. Some additional adjustment may be necessary if the label was not 
perfectly aligned to begin with. See Section 4E. 

 
 
 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for I Candy 200









































































Reviews: