iColor I Candy 200 User Manual Download Page 41 | Manualshive

Page: 41 / 72

background image

|

40

User Manual – February 2020 Edition

Print Quality

There are 4 levels of print quality in the driver. The lower the quality, the faster the print. Quality 1 provides
the fastest print available while Quality 4 provides the best quality. It is recommended that you experiment with the
different levels when designing your label to find a good balance between print quality and print speed. Quality 2
is the default.

Color Matching

There are several options available depending on which cartridge is installed (Pigment or Dye). The options will
update automatically depending on which cartridge is installed.

Vivid Graphics mode is best used for graphical images where accurate color reproduction is not as essential.
Images printed in this mode will look more vibrant because more ink is being used to produce them. However,
printing images of people may produce skin tones that have a reddish tint.

Vivid Photos mode is best used for photographic images where accurate color reproduction is very essential.
Images printed in this mode will look lighter than those printed in Vivid Graphics mode. Skin tones especially
will look more natural in this mode.

ICC Gloss Paper, ICC Gloss Polyester and ICC Matte Bopp are all ICC calibrated color matching options. Select
the setting that corresponds to your installed media of the same type to produce ICC color matched prints.
NoteICC monitor calibration and additional setup is required for this option to work. -NONE- will use no color
matching.

Ink Saturation

This option controls the amount of ink used when printing an image. The default setting is 100%, which will
provide the most accurate color matching. If the ink is not drying fast enough or “bleeding”, you can decrease
the Ink Saturation to lessen the amount of ink that is applied to the label.

Rotate 180 Degrees

Set this setting to Yes to print with the labels right side up as they exit the printer.

Enable Bi-di

Set to “Yes” for fastest print speed. Requires an alignment print after every cartridge change. Set to “No” for better
quality print (in some cases).

Launch IColor 200 PrintHub

This setting will open the IColor 200 PrintHub application.

Details

Select this setting to see current firmware and driver version information and other printer settings.

«
...
39
40
41
42
43
...
»

Summary of Contents for I Candy 200









































































Reviews:

No comments

Related manuals for I Candy 200

Brand: Faema Pages: 328

Brand: 9BARISTA Pages: 8

Brand: Gaggia Pages: 4

Brand: Gaggia Pages: 4

Brand: Gaggia Pages: 4

Brand: Gaggia Pages: 4

Brand: Gaggia Pages: 4

Brand: Gaggia Pages: 4

Brand: Gaggia Pages: 4

Brand: Gaggia Pages: 68

Brand: Baratza Pages: 11

Brand: Magic Chef Pages: 20

Brand: EOS Pages: 58

Intuition Preference EA87 Series

Brand: Krups Pages: 154

Brand: U-Line Pages: 55

Brand: MTN Products Pages: 3

Brand: Tupperware Pages: 47

U-3018CLRINT-40C

Brand: U-Line Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands