iColor I Candy 200 User Manual Download Page 19 | Manualshive

Page: 19 / 72

background image

|

18

User Manual – February 2020 Edition

Present Options

Do Not Present

In this mode the label stock does not move after the last label is printed. This means that part of the last label
printed is still in the printer. This should be used only if you have a label rewinder attached.

Present After No Activity

This setting will present (feed all printed labels past the tear off point) at the end of a print job if the printer does
not receive another print job within one second of the last print job in the queue. You can use this feature to
present at the end of a multi-copy job, a multi-page job or multiple individual jobs in the queue.

«
...
17
18
19
20
21
...
»

Summary of Contents for I Candy 200









































































Reviews:

No comments

Related manuals for I Candy 200

Brand: lancer Pages: 8

Brand: Haden Pages: 9

Brand: Qilive Pages: 72

Brand: illy Pages: 9

Brand: La Pavoni Pages: 8

Dymo LabelWriter 450 Twin Turbo

Brand: U-Line Pages: 9

Dough Stretcher

Brand: AMF Pages: 2

Brand: ELEKTRA Pages: 6

BARISTA AROMA SOLO

Brand: STARBUCKS Pages: 40

Brand: Teka Pages: 118

Nespresso Vertuo Creatista

Brand: Sage Pages: 28

Brand: Optimum Pages: 10

Fantasia EB-FT3

Brand: Evebot Pages: 8

Brand: Rancilio Pages: 34

Brand: Klarstein Pages: 64

Brand: Klarstein Pages: 56

Brand: CBTL Pages: 20

Brand: Philips Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands