Page 30
autocut 5-32cts user manual edItIon II 2015-01-16
5.6.7 order, Run view
this order menu is similar to the red order menu but it contain only the necessary
buttons and informations for running the order, the chosen parameters cannot be
changed here.
1. open belt:
press to open the belt unit and release the hose.
2. oFF/oN:
shows the status of the automatic sequence.
3. Close belt.
press to close the belt unit.
4. Cycle Start:
press to close the belt and start the automatic cut sequence.
5. Cycle Stop:
press to stop the cut sequence.
6. Info field:
Information will display here such as:
7. Select order:
press to open the red ordermenu with possibilities to
change the parameters.
8. Home:
Closes this menu and open ”Main”menu.
9. Quant.Finish:
Information about cut quantity per row.
this button is always showed after a zero cut, press it to get 1
piece without adding one to the finished quantity or press ”Cycle
Start”.
no hose detected by the inlet hose sensor.
or a hose joint detected by the jointsensor (option)
the control measuringsystem has detected a difference
compared to requested length that is exceeding the
chosen length tolerances.
HYDROSCAND MACHINE AB
Kungsvägen 22
Phone: +46 (0)225 - 573 30
S-783 35 Säter
Fax:
+46 (0)225 - 501 08
Sweden
Web:
www.hydroscand-machine.se
Edition 7-00
MANUAL-E
Page 19
This order menu is similar to the red order menu but it contain only the necessary
buttons and informations for running the order, the chosen parameters cannot be
changed here.
1.
Open Belt:
Press to open the belt unit and release the hose.
2.
OFF/ON:
Shows the status of the automatic sequence.
3.
Close Belt.
Press to close the belt unit.
4.
Cycle Start:
Press to close the belt and start the automatic cut sequence.
5.
Cycle Stop:
Press to stop the cut sequence.
6.
Info field:
Information will display here such as:
7.
Select Order:
Press to open the red order menu with possibilities to
change the parameters.
8.
Home:
Closes this menu and open "Main" menu.
9.
Quant.Finish:
Information about cut quantity per row.
7.4 Order, Run view
This button is always showed after a zero cut, press it to
get 1 piece without adding one to the finished quantity or
press "Cycle Start".
No hose detected by the inlet hose sensor.
Or a hose joint detected by the Jointsensor (option)
The control measuringsystem has detected a difference
compared to requested length that is exceeding the
chosen length tolerances.
5
6
4
1
2
3
9
7
8
HYDROSCAND MACHINE AB
Kungsvägen 22
Phone: +46 (0)225 - 573 30
S-783 35 Säter
Fax:
+46 (0)225 - 501 08
Sweden
Web:
www.hydroscand-machine.se
Edition 7-00
MANUAL-E
Page 19
This order menu is similar to the red order menu but it contain only the necessary
buttons and informations for running the order, the chosen parameters cannot be
changed here.
1.
Open Belt:
Press to open the belt unit and release the hose.
2.
OFF/ON:
Shows the status of the automatic sequence.
3.
Close Belt.
Press to close the belt unit.
4.
Cycle Start:
Press to close the belt and start the automatic cut sequence.
5.
Cycle Stop:
Press to stop the cut sequence.
6.
Info field:
Information will display here such as:
7.
Select Order:
Press to open the red order menu with possibilities to
change the parameters.
8.
Home:
Closes this menu and open "Main" menu.
9.
Quant.Finish:
Information about cut quantity per row.
7.4 Order, Run view
This button is always showed after a zero cut, press it to
get 1 piece without adding one to the finished quantity or
press "Cycle Start".
No hose detected by the inlet hose sensor.
Or a hose joint detected by the Jointsensor (option)
The control measuringsystem has detected a difference
compared to requested length that is exceeding the
chosen length tolerances.
5
6
4
1
2
3
9
7
8