Hussmann RL2SP Installation & Operation Manual Download Page 45 | Manualshive

Page: 45 / 65

background image

3-2

D

rIp

p

IpIng

anD

s

plashguarDs

P/N 3053328_C

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM

1. Tee is factory-installed. Do not overtighten

threads, or the drain fitting or tee may become
damaged.

2. Do NOT use thread sealer on ABS drain fitting.

If sealer is used the ABS drain fitting may crack
or leak! (If a tee needs to be installed it should
be tightened no more than 4 turns.) Do not
overtighten threads.

3. Dry fit the supplied water seal / trap to ensure

approximately

1

/

2

in. of clearance from the

bottom of the trap to the floor as shown.

NOTE: It may be necessary to rotate water seal (trap)
inside the tee a few degrees to ensure clearance at
two locations. There must be clearance 1) between
the bottom of the water seal and the floor, and 2)
between the top of the water seal outlet and the
bottom of the merchandiser. Do not over-rotate or
gravity seal may be compromised. Always rotate trap
bottom toward merchandiser support rail.

1

/

2

in. Clearance to Floor

Approx.

Factory-Installed

Tee Fitting

Factory Installed (four turns)

Do NOT use Thread Sealer on Drain Fitting!

(Drain Fitting)

Rotate Water Seal

towards back of

Merchandiser if required

Field-Installed
Drop Piping

Merchandiser
Bottom

Waste Outlet
(Drain Fitting)

Field-Installed
Coupling

Field-Installed
Water Seal

Factory Installed (four turns)

Field-Installed
Plug

Field-Installed
Adapter

Factory-Installed

Tee Fitting

Do NOT use Thread Sealer on Drain Fitting!

Front of

Merchandiser

Merchandiser

Bottom

Waste
Outlet

Maintain Clearance
to Bottom of Case

Field-Installed
Water Seal

Floor

Rotate Water Seal towards
back of Merchandiser if
required

1

/

2

in. Clearance to

Floor

TEE-SIDE

Approx.

1

/

2

in. Clearance to Floor

«
...
43
44
45
46
47
...
»

Summary of Contents for RL2SP


































































Reviews:

No comments

Related manuals for RL2SP

ECO MIDI FG 60 G

Brand: Gram Pages: 26

Brand: Hussmann Pages: 26

Kool-It KCD-36R

Brand: MVP Pages: 6

IMPACT Elite E3-XC

Brand: Hussmann Pages: 8

Brand: Hussmann Pages: 7

Brand: Hussmann Pages: 6

Brand: True Pages: 2

Brand: Federal Pages: 69

Brand: Crane Pages: 3

Brand: Crane Pages: 53

Refreshment Center 784

Brand: Crane Pages: 59

Brand: Crane Pages: 101

Brand: Crane Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands