Hussmann RL2SP Installation & Operation Manual Download Page 4

Page: 4 / 65

IMPORTANT

KEEP IN STORE FOR FUTURE REFERENCE

Quality that sets industry standards!

12999 St. Charles Rock Road • Bridgeton, MO 63044-2483

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900

www.hussmann.com

Merchandiser must operate for 24 hours

before loading product!

Regularly check merchandiser temperatures.

Do not break the cold chain. Keep products

in freezer before loading into merchandiser.

These merchandisers are designed

for only pre-frozen products.

ATTENTION

Merchandiser must operate for 24 hours before

loading product!

Regularly check merchandiser temperatures.

Do not break the cold chain. Keep products in freezer

before loading into merchandiser.

Medium temperature merchandisers are designed for

loading ONLY pre-chilled products.

Low temperature merchandisers are designed for

loading ONLY frozen products.

Summary of Contents for RL2SP


































































Search results

Summary of Contents for RL2SP

Reviews:

Related manuals for RL2SP

Brands by name

Popular brands

Hussmann RL2SP, Installation & Operation Manual

Search results

Summary of Contents for RL2SP

Reviews:

Related manuals for RL2SP

Brands by name

Popular brands