Hussmann RL2SP Installation & Operation Manual Download Page 9

Page: 9 / 65

Reach-In

P/N 3053328_C

1-3

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

NOTE:

egin

lineup

leveling

from

the

highest

point

the

store

floor

Place shims under the rail and make sure that they
are positioned at a base component (crossbar). This
transfers the weight directly from the loaded case
through to the floor.

Placing shims at other locations will cause uneven
distribution of weight leading to piping leaks, as well
as sagging or wracked doors.

Bottom front supports must be shimmed if not in full
contact with the floor.

Front

Back

Base Component

Shim Here

It is the installing contractor’s

responsibility to consult local agencies

for local code requirements.

4-Door Shown

Approximately
Centered

Rear of Reach-in

Base Component

Shim

Here

Back

Skid/External Base

Bottom Front

Support

Front

Electrical Wireway

Summary of Contents for RL2SP


































































Search results

Summary of Contents for RL2SP

Reviews:

Related manuals for RL2SP

Brands by name

Popular brands

Hussmann RL2SP, Installation & Operation Manual

Search results

Summary of Contents for RL2SP

Reviews:

Related manuals for RL2SP

Brands by name

Popular brands