Hussmann RL2SP Installation & Operation Manual Download Page 16 | Manualshive

Page: 16 / 65

background image

1-10

I

nstallatIon

P/N 3053328_C

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM

Figure 5A, Part 2. Apply Gaskets to Right End

RL / RLN

Apply gasket pad to right end
first, then apply the narrower
Foam Tape Gasket — 3
around the perimeter of the
right end frame outside of
the donut gasket as shown in
Figure 5A, Part 2, 5B or 5C,
Part 2.

•  Lap gaskets at lower
corners.
•  Check that there are no
gaps between gasket and case.
•  Do not stretch gasket,
especially around corners.
To make sharp corners, paper
backing can be torn without
removing from gasket.

•  Do not butt gaskets; always
lap joints.
•  Remove paper backing after
gasket is applied to keep gasket
free of debris.
•  Gasket has high tack
adhesive and must be properly
placed the first time.

Overlap

Gasket

Gasket Pad

F

R

O
N

T

Right End

Left E

nd

F

R

O
N

T

/ / / / / / /

/////////////////////////////

2

3

/////////////////////////////

Detail D

1

Overlap

Foam Gasket 3

as Shown

/////////////////////////////

1

2

3

/////////////////////////////

Detail A

/ / / / / / / /

/////////////////////////////

1
2
3

Donut Gasket

Foam .906 inch x 1/2 inch x 200 inch

Foam 1/2 inch x 1/4 inch

Right End

Case-to-Case

Joint or End Panel

Apply Donut Gasket,

Foam Gaskets

and Gasket Pad to

Right End Only

Apply Gasket Pad

2

Detail C

Install Donut

Gasket

(seat into groove)

Left End

Only Use

Donut Gasket on

left end of

a Case-to-Case

Joint

If attaching an End

Panel, all 4 Gaskets

must be applied.

1. Butyl is NOT an acceptable
substitute for donut or foam
gasket.

Gasket
Pad

Overlap

Foam Gasket

As Shown

DETAIL A

Right End

Left End

Foam 1/2 inch x 1/4 inch

Donut Gasket

Foam .906 inch x 1/2 inch x 200 inch

Install Donut Gasket

(seat into groove)

Left End

Only Use Donut

Gasket on left end
of a Case-to-Case

Joint

If attaching an End

Panel, all 4 Gaskets

must be applied.

Right End Case-to-Case

Joint or End Panel

Apply Donut Gasket,

Foam Gaskets and

Gasket Pad to Right

End Only

Apply Gasket Pad

Detail C

Make sure area where raceway attaches to end frame

is sealed with the wider 1 in. x

1

/

2

in. gasket.

F

R

O

N

T

F

R

O

N

T

«
...
14
15
16
17
18
...
»

Summary of Contents for RL2SP


































































Reviews:

No comments

Related manuals for RL2SP

Brand: Hussmann Pages: 29

Mobile Merchandiser MM4

Brand: BKI Pages: 24

Brand: Hussmann Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands