Hussmann RL2SP Installation & Operation Manual Download Page 23 | Manualshive

Page: 23 / 65

background image

Reach-In

P/N 3053328_C

1-17

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

INSTALLING BUMPERS

Offsetting the bumpers and top rails helps to
disguise the joint locations, giving the lineup a
smoother look.

Begin at the left end of the line-up. A starter bumper is
factory-installed with end kits. Insert the internal joint
trim, then add the full-length bumper.

Align each bumper section with its retainer and push
into place, working from the end of the lineup. Install
full length bumpers and internal joint trims offset
across joints. Make sure that no gaps exist between
sections. Continue installing bumpers the length of the
line up.

Do NOT install the last bumper sections at this time.
These sections will be installed in the last step.

Once all except the last section of bumper have been
installed, refrigerate the case line-up for at least six
(6) hours. The last sections of bumper should be kept
inside a refrigerated case or cooler during this time to
allow the bumpers to contract.

Before installing the last full-length section, measure
the remaining space. Use a miter box and fine-tooth
saw to cut last bumper to length. Install the last section.
Remove protective film from bumpers once installation is
complete. Optional end bumpers are factory-installed.

Bumper End Caps can be adjusted horizontally to
eliminate gaps.

Merchandiser
Joint

Merchandiser
Joint

Internal Joint
Trims

Starter
Bumper

Full Length
Bumpers

Bumper

Miter Box

«
...
21
22
23
24
25
...
»

Summary of Contents for RL2SP


































































Reviews:

No comments

Related manuals for RL2SP

Brand: Hussmann Pages: 31

Brand: Federal Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands