Hussmann RL2SP Installation & Operation Manual Download Page 3 | Manualshive

Page: 3 / 65

background image

BEFORE YOU BEGIN

Read these instructions completely and carefully.

PERSONAL PROTECTION EQUIPMENT (PPE)

Personal Protection Equipment (PPE) is required whenever installing or servicing this equipment. Always wear
safety glasses, gloves, protective boots or shoes, long pants, and a long-sleeve shirt.

1. If the information in these instructions are not followed exactly, a fire or explosion may result, causing

property damage, personal injury or death.

2. Installation and service must be performed by a qualified installer or service agency.
3. This unit is designed only for use with R-290 (propane) gas as the designated refrigerant.

THE REFRIGERANT LOOP IS SEALED. ONLY A QUALIFIED TECHNICIAN SHOULD ATTEMPT TO
SERVICE!

•  Propane is flammable and heavier than air.
•  It collects first in the low areas but can be circulated by the fans.
•  If  R-290 (propane) is present or even suspected, do not allow untrained personnel to attempt to find the cause.
•  The propane gas used in the unit has no odor.
•  The lack of  smell does not indicate a lack of  escaped gas.
•  If  a leak is detected, immediately evacuate all persons from the store, and contact the local fire department to

advise them that a pro pane leak has occurred.

• Do not let any persons back into the store until the qualified service technician has arrived and that

technician advises that it is safe to return to the store.

• A hand-held propane leak detector (“sniffer”) shall be used before any repair and/or maintenance.
• No open flames, cigarettes or other possible sources of ignition should be used inside the building where

the units are located until the qualified service technician and/or local fire department determines that all
propane has been cleared from the area and from the refrigeration systems.

• Component parts are designed for propane and non-incendive and non-sparking. Component parts shall only

be replaced with identical repair parts.

FAILURE TO ABIDE BY THIS WARNING COULD RESULT IN AN EXPLOSION, DEATH, INJURY AND
PROPERTY DAMAGE.

Reach-In

P/N 3053328_C

iii

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

«
1
2
3
4
5
...
»

Summary of Contents for RL2SP


































































Reviews:

No comments

Related manuals for RL2SP

Advantage Series

Brand: Tyler Pages: 21

Brand: ChefLine Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands