Husqvarna FE 450 Owner'S Manual Download Page 57

Page: 57 / 128

12 SERVICE WORK ON THE CHASSIS

K00589-11

–

Position the frame protectors on the left and right.

–

Mount and tighten screws



Guideline

Screw, frame protector

3 Nm (2.2 lbf ft)

–

Mount and tighten screws



with the washers.

Guideline

Screw, frame protector

3 Nm (2.2 lbf ft)

–

Mount the new cable ties.

Finishing work

–

Check the free travel of the foot brake lever. (

p. 75)

–

Remove the motorcycle from the lift stand. (

p. 45)

12.18

Removing the seat

Preparatory work

–

Remove the air filter box cover. (

p. 56)

F00296-10

Main work

–

Remove screw



–

Pull seat back and lift it off.

12.19

Mounting the seat

F00297-10

Main work

–

Mount the front of the seat on the collar bushing of the fuel tank, lower the seat at

the rear, and push the seat forward.

–

Make sure that the seat is correctly locked in.

–

Mount and tighten screw



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Install the air filter box cover. (

p. 56)

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands