Husqvarna FE 450 Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 128

background image

6

CONTROLS

18

6.15

Idle speed adjusting screw

F00448-10

The idle speed is adjusted using the idle speed adjusting screw



.

Increase the idle speed by turning the idle speed adjusting screw clockwise.
Decrease the idle speed by turning the idle speed adjusting screw counterclockwise.
The idle setting of the throttle valve body has a big influence on the vehicle's starting

behavior, on stable idling, and on vehicle response when the throttle is opened.
An engine with a correctly set idle speed is easier to start than an engine with the idle

speed set incorrectly.

6.16

Shift lever

401950-10

The shift lever



is fitted on the left side of the engine.

401950-11

The gear positions can be seen in the photograph.
The neutral or idle position is between the first and second gears.

6.17

Foot brake lever

401956-10

The foot brake lever



is attached in front of the right footrest.

The foot brake lever is used to activate the rear brake.

«
...
18
19
20
21
22
...
»

Summary of Contents for FE 450

































































































































Reviews:

No comments

Related manuals for FE 450

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

Brand: Memphis Shades Pages: 2

Yamaha X-MAX 300

Brand: BRUUDT Pages: 7

Brand: MV Agusta Pages: 36

Brand: Gentex Pages: 15

Brand: Apollo Pages: 92

Brand: R&G Pages: 26

Brand: Denali Pages: 2

Compu-Fire 55120 32

Brand: PerTronix Pages: 3

Brand: DYNATEK Pages: 11

Evoline 3 Series

Brand: Shark Pages: 31

Brand: Shark Pages: 36

Brand: Sundstrom Pages: 68

Brand: SUR-RON Pages: 37

MSS X9 EVOLUTION 250

Brand: PIAGGIO Pages: 262

MP3 500 ie SPORT Business LT 2011

Brand: PIAGGIO Pages: 375

Brand: R&G Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands