Husqvarna FE 450 Owner'S Manual Download Page 105

Page: 105 / 128

18 SERVICE WORK ON THE ENGINE

103

F00438-10

Main work

–

Check the engine oil level.

Info

After switching off the engine, wait one minute before checking the level.

The engine oil is at a level between the lower edge



and the middle



the level viewer.

» If the engine oil is not up to the lower edge



of the level viewer:

–

Add engine oil. (

p. 105)

18.3

Changing the engine oil and oil filter, cleaning the oil screens

Warning

Danger of scalding

Engine and gear oil get very hot when the motorcycle is ridden.

–

Wear suitable protective clothing and safety gloves.

–

In the event of scalding, rinse the area affected immediately with lukewarm water.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

Info

Drain engine oil with engine at operating temperature.

Preparatory work

–

Remove the engine guard. (

p. 70)

–

Park the motorcycle on a level surface.

F00441-10

Main work

–

Place a suitable container under the engine.

–

Remove oil drain plug



with the magnet and seal ring.

F00442-10

–

Remove screw plug



with the short oil screen and the O-rings.

Info

Do not remove screw



F00443-10

–

Remove screw plug



with the long oil screen



and the O-rings.

–

Completely drain the engine oil.

–

Thoroughly clean the parts and sealing surfaces.

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands