Husqvarna FE 450 Owner'S Manual Download Page 112

Page: 112 / 128

21 TROUBLESHOOTING

110

Faults

Possible cause

Action

Engine overheats

Foam formation in cooling system

–

Drain the coolant.

(

p. 95)

–

Refill the coolant.

(

p. 96)

Bent radiator hose

–

Change the radiator hose.

Thermostat defective

–

Check the thermostat.
Guideline
Opening temperature: 70 °C (158 °F)

Defect in radiator fan system

–

Check fuse

–

Check the radiator fan.

Malfunction indicator lamp lights up

or flashes

Defect in fuel injection system

–

Stop the motorcycle and identify the faulty

part using the blink code.

–

Check the cabling for damage and the electri-

cal plug-in connectors for corrosion and dam-

age.

–

Read out the fault memory using the Husq-

varna Motorcycles diagnostics tool.

High oil consumption

Engine vent hose bent

–

Route the vent hose without bends or replace

it if necessary.

Engine oil level too high

–

Check the engine oil level. (

p. 102)

Engine oil too thin (low viscosity)

–

Change the engine oil and oil filter and clean

the oil screens.

(

p. 103)

Piston and cylinder worn

–

Measure the piston/cylinder mounting clear-

ance.

Battery discharged

Battery is not being charged by alter-

nator

–

Check the charging voltage.

–

Check the stator winding of the alternator.

Undesired power consumer

–

Check the closed current.

Speedometer values deleted (time,

stop watch, lap times)

The battery in the speedometer is

discharged

–

Change the speedometer battery. (

p. 92)

The high beam, low beam, tail light,

parking light, and license plate lamp

are not working

Fuse

blown

–

Change the fuses of individual power con-

sumers. (

p. 88)

The speedometer, horn, brake light,

turn signal, and radiator fan are not

working

Fuse

blown

–

Change the fuses of individual power con-

sumers. (

p. 88)

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands