Husqvarna FE 450 Owner'S Manual Download Page 90

Page: 90 / 128

15 ELECTRICAL SYSTEM

F00358-10

–

Take off protection caps



–

Remove faulty main fuse



Info

You can recognize a defective fuse by a burned-out fuse wire



A spare fuse



is located in the starter relay.

–

Install a new main fuse.

Fuse (58011109120) (

p. 114)

–

Check that the electrical equipment is functioning properly.

Tip

Insert a spare fuse so that it is available if needed.

–

Mount the protection caps.

–

Mount the starter relay onto the holder and route the cable.

Finishing work

–

Mount the seat. (

p. 55)

–

Install the air filter box cover. (

p. 56)

15.5

Changing the fuses of individual power consumers

Info

The fuse box containing the fuses of individual power consumers is located under the seat.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the air filter box cover. (

p. 56)

–

Remove the seat. (

p. 55)

F00359-10

Main work

–

Pull EFI control unit



from the holder and hang it to one side.

F00360-10

–

Open fuse box cover



–

Remove the defective fuse.
Guideline

(FE EU)

Fuse

‑

10 A - EFI control unit, lambda sensor, speedometer, combination

switch (optional), fuel injection, diagnostics connector, fuse

(FE AU)

Fuse

‑

10 A - EFI control unit, speedometer, combination switch

(optional), fuel injection, diagnostics connector, fuse

Fuse

- 10 A - high beam, low beam, parking light, tail light, license plate lamp

Fuse

- 10 A - radiator fan, horn, brake light, turn signal

Fuse

- 5 A - fuel pump

Fuses

res

- 10 A - spare fuse

Info

You can recognize a defective fuse by a burned-out fuse wire



Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands