Husqvarna FE 450 Owner'S Manual Download Page 58

Page: 58 / 128

12 SERVICE WORK ON THE CHASSIS

12.20

Removing the air filter box cover

F00457-10

–

Pull off the air filter box cover sideways in areas





and



, and remove

toward the front.

12.21

Installing the air filter box cover

F00456-10

–

Position air filter box cover on collar bushings



and



and push toward the

rear.

–

Engage the air filter box cover in areas





and



12.22

Removing the air filter

Note

Engine damage

Unfiltered intake air has a negative effect on the service life of the engine.

Dust and dirt will enter the engine without an air filter.

–

Never start to use the vehicle without an air filter.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable

regulations.

Preparatory work

–

Remove the air filter box cover. (

p. 56)

F00300-10

Main work

–

Detach retaining tab



. Remove air filter with air filter support.

–

Remove air filter from air filter support.

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands