Husqvarna FE 450 Owner'S Manual Download Page 115

Page: 115 / 128

22 TECHNICAL DATA

113

22.3

Capacities

22.3.1

Engine oil

Engine oil

1.2 l (1.3 qt.)

Engine oil (SAE 10W/50) (

p. 117)

22.3.2

Coolant

Coolant

1.2 l (1.3 qt.)

Coolant (

p. 117)

22.3.3

Fuel

Total fuel tank capacity,

approx.

8.5 l (2.25 US gal)

Super unleaded (ROZ 95/RON 95/PON 91) (

p. 117)

Fuel reserve, approx.

1.5 l (1.6 qt.)

22.4

Chassis

Frame

Central tube frame made of chrome molybdenum steel tubing

Fork

WP Performance SystemsXplor 48

Suspension travel

Front

300 mm (11.81 in)

Rear

330 mm (12.99 in)

Fork offset

22 mm (0.87 in)

Shock absorber

WP Performance Systems

5018 DCC Link

Brake system

Disc brakes, brake calipers on floating bearings

Brake discs - diameter

Front

260 mm (10.24 in)

Rear

220 mm (8.66 in)

Brake discs - wear limit

Front

2.5 mm (0.098 in)

Rear

3.5 mm (0.138 in)

Tire air pressure off road

Front

1.0 bar (15 psi)

Rear

1.0 bar (15 psi)

Road tire pressure

Front

1.5 bar (22 psi)

Rear

1.5 bar (22 psi)

Final drive (All 450 models)

14:52 (13:52)

Final drive (All 501 models)

14:50 (13:50)

Chain

5/8 x 1/4"

Rear sprockets available

48, 50, 52

Steering head angle

63.5°

Wheelbase

1,495±10 mm (58.86±0.39 in)

Seat height unloaded

970 mm (38.19 in)

Ground clearance unloaded

370 mm (14.57 in)

Weight without fuel, approx. (All 450 models)

107.8 kg (237.7 lb.)

Weight without fuel, approx. (All 501 models)

108.4 kg (239 lb.)

Maximum permissible front axle load

145 kg (320 lb.)

Maximum permissible rear axle load

190 kg (419 lb.)

Maximum permissible overall weight

335 kg (739 lb.)

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands