Husqvarna FE 450 Owner'S Manual Download Page 75

Page: 75 / 128

13 BRAKE SYSTEM

Preparatory work

–

Check the front brake linings. (

p. 73)

F00312-10

Main work

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

–

Remove screws



–

Remove cover



with membrane



–

Add brake fluid to level



Guideline

Level



(brake fluid level below

reservoir rim)

5 mm (0.2 in)

Brake fluid DOT 4 (

p. 117)

–

Position the cover with the membrane. Mount and tighten the screws.

Info

Clean up overflowed or spilled brake fluid immediately with water.

13.6

Checking the front brake linings

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcycles workshop will be

glad to help.)

F00328-10

–

Check the brake linings for minimum thickness



Minimum thickness



≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the front brake linings.

(

p. 73)

–

Check the brake linings for damage and cracking.
» If damage or cracking is visible:

–

Change the front brake linings.

(

p. 73)

13.7

Changing the front brake linings

Warning

Danger of accidents

Incorrect maintenance will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized Husqvarna Motorcycles workshop

will be glad to help.)

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands