Husqvarna FE 450 Owner'S Manual Download Page 23

Page: 23 / 128

SPEEDOMETER

7.1

Speedometer overview

401908-10

Indicator lamps overview (

p. 16)

Left button

Display

Right button

7.2

Activation

401908-01

Activating the speedometer

The speedometer is activated when one of the buttons is pressed or an impulse

comes from the wheel speed sensor.

7.3

Message on the speedometer

401901-01

Possible states

Battery voltage of the speedometer

–

Battery voltage of the

speedometer is too low. Change the battery.
Service

–

A service is due. Contact an authorized Husqvarna Motorcy-

cles workshop.

7.4

Setting the speedometer

Condition

The motorcycle is stationary.

401909-01

–

Press both buttons for 3

–

5 seconds.

The Setup menu is displayed. The

UNIT

display flashes.

–

Press one of the buttons to select

UNIT

for the speed in kilometers

KM/H

miles

M/H

401911-01

–

Wait for 5 seconds.

The speedometer changes to the next menu item. The

symbol flashes.

–

Press one of the buttons to select the 24h or 12h display of the clock.

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands